Gioia Wall Art

Tapestry, Arch Door Wall Decal

$99.99 AUD
  • Arch door shape Peel & Stick wall decal.
  • Easy application and clean removal. Suitable for both renters and homeowners. 
  • All the arch door decals will come as one piece.
  • DIY-friendly, can be easily installed, no pastel is required. No mess, no fuss
  • Rolled up in a sturdy tube, with an installation guide.
  • Eco-friendly. The wallpaper fiber has a matt finish, is nontextured, nonwoven, and is 100% PVC-free. 
  • Printed with ECOLOGO® Certified and GREENGUARD GOLD Certified HP Latex printer. No nasty odd, no drama.
  • Click here for the full installation guide. We will also attach the guide with your order. 

  • Can be reused if the wall was prepared properly.

    This wall paper is self-adhesive backed. The adhesive is designed for easy application and clean removal.

    Prepare Your Wall

    The wall surface should be clean, dry, structurally sound and free of mildew, grease, or other stains, and free of irregularities in order to achieve the best results.This will also ensure clean complete removal when redecorating.

    To apply on drywall.

    For best results, apply to a wall surface that has been painted with one coat of builder’s primer and one coat of water based paint (note: this is typical of new construction; a wall surface that has been painted with a single coat of primer or a coat of satin or gloss paint is acceptable).

    The wall surface should be clean, smooth, and free of debris or contaminants.

    To apply over paint.

    Painted walls should be primed, smooth, and free from debris. Check the wall surface to determine the condition of the paint adhesion. If the paint is old, damaged, or flaking, priming is highly recommended.

    To apply to a wall previously covered with wall paper.

    Any old wall paper remaining should be removed as well as the old adhesive (remove by sanding or using adhesive remover). Primer should be applied to the wall surface that is clean, smooth, and free of the old adhesive. 

    To apply over paneling.

    Any grooves should be filled to achieve a smooth surface, then covered with an adhesion-promoting primer.

    Application

    • Equipment – a step ladder, a sharp knife, a spirit level, and maybe a second pair of hands. Make sure your hands are clean and dry. Inspect your wall and remove any picture hooks and any switch plates.
    • To remove the wallpaper from the tube (it can be tight), grab the corners from the inside the roll and, with the roll turned on it’s side, twist the panels until you feel movement – this should allow enough space to pull the panels out.
    • Start From the Left – start hanging panels on the left side of the wall, either according to the number written on the back, or just one by one. Take your time on this first panel, making sure it is level at the top. If the wall is adjoining another wall, you may need to slightly overhang Panel 1 on the left side and trim later, if the wall is not perfectly square.
    • Prepare To Stick –  lay the panel face down on a flat surface (somewhere clean) and peel back about 30cm of backing paper and fold it back sharply (so it stays out of the way). Do not let any debris stick to the adhesive.
    • Stick – line up the top edge of the wallpaper with the top of the wall and then stick it to the wall. If it is not square, peel it off and reapply.
    • Remove The Backing Paper – once in place, stick it to the wall. Carefully pull the backing paper down from behind the panel in stages, in a slow and even fashion. Let the wallpaper fall naturally into place, smoothing it to the wall with your hand in a down and outwards motion to remove any bubbles.
    • Wrinkles and Bubbles – all bubbles should just smooth out. If they don’t or a crease occurs, just peel up the panel and reapply rather than rubbing the print.
    • Additional Panels – align the next panel to the first panel, and remove the backing paper and stick to the wall as per the previous instructions.
    • If the design is not lining up, once the backing paper is removed from the panel, pull it away from the wall, drop it down 10cm from the top of the wall, align at eye level, smooth it onto the wall from the centre back to the top and to the bottom. Just keep the back of the panel from adhering to itself.
    • Trimming – when all the panels have been adhered, use a sharp knife to remove any excess at the base of the wall. Carefully trim around the power points and light switches after pulling the plate off if necessary.

    All the items are made-to-order in Melbourne. Your wallpaper and decal will be rolled up in a mailing tube. If you order a large size of wallpaper, they may come in more than one tubes. You will receive a notification email with tracking information when your order is on its way to you.  

    Production Time

    Normally your order will be dispatched within 3 business days.

    Shipping
      How long it will take after dispatch?

    FREE

    Standard Shipping

    3-5 business days for metro areas. 5-10 business days for orders to WA & NT & TAS and rural areas. 

    Express Shipping

    1-4 business days, depending on where you are. 

    There will be extra cost calculated at checkout.

    Local Pickup

    Pick up from our workshop in Blackburn North VIC 3130.

    We will email you when your order is ready. Then you can come over anytime during 9am-5pm Mon.-Fri. except public holidays.

     

    If you have any questions, please feel free to contact us anytime.